Accessories and Cables

BNC plug to 4mm Adapter

Hook-type hook probe with 10mm coated limette hook, 1000 volts CAT III 20 amps (Black).

Option for the SSA3000X model. Utility Kit: N (M) -SMA (M) cable, N (M) -N (M) cable, N (M) -BNC (F) adapter (2 pcs), N (M) -SMA (F) adapter (2 pcs), 10 dB attenuator

Option for Model SSA3000X. N-SMA cable, 6GHz bandwidth

Rackmount kit is designed for use with only one instrument, is compatible with the SDG800, SDG1000 and SDG5000 series function generator

USB-GPIB Adapter, USB Device expanded into GPIB interface.

Passive tips. 10X CAT II 1000V, CAT III 600V, 250M-bandwidth, accessory for the portable oscilloscope SHS1000

Passive tips. bandwidth: 50MHz; Maximum continuous current 30Arms; Peak current 50A; Ranges? 5A / 30A; Presicion? 5A (± 1% ± 1mA); 30A (± 1% ± 10mA); Power Eliminator included DC12V / 1.2A

Differential points. bandwidth: 100MHz; Maximum differential input voltage 7000V (DC + Peak AC); Range (attenuation): 100X / 1000X; Presicion: ± 2%; DC5V / 1.A USB included Eliminator power

>Differential Probe. Bandwidth: 100MHz; Maximum input differential voltage 7000V(DC + Peak AC);Range selection (attenuation ratio): 100X/1000X; Accuracy: ±2%; Standard 5V/1A USB power adapter

Current clamp measures AC and DC currents up to 200/2000 amps, two current ranges controlled by selector switch, zero offset button, BNC type connector, screened lead for noise suppression.

Oscilloscope Model SDS1000CML + / DL +. 100MHz; 2 channels; 1GSa / s; 2M memory points; 7 "display (8 * 16div); Supports USBTMC protocol and SCPI commands

For SDM3055 and SDM 3065X, multiplexer that provides multi-point measurement capabilities to the SDM3000 series of digital multimeters. The scanner features 12 multi-purpose + 4 current channels and supports the following measurement functions: DCV, ACV, DCI, ACI, 2WR, 4WR, CAP, FREQ, DIODE, CONT and TEMP (RTD and Thermocouple) It must be purchased and factory installed with a new DMM.

Modulation of the pulse train? Option?

Rack Mount kit.

I2S serial triggering and decoding,software license.

Non-contact near-field probes Kit. Includes: Three magnetic near-field probes (20, 10, 5mm resolution), one electric field point probe (5mm resolution), N-to-SMA adapter, and cable in a handy soft carrying case. Operating frequency range: 300kHz~3GHz.

Bandwidth: DC-600 kHz ; Current Range: L(50mA~10A Peak), H(1A~100A Peak); Attenuation accuracy L(0.1V/A), H(0.01V/A); Typical DC precision: L(3%±50mA),H(500mA~40A Peak :4%±50mA;40A~100A Peak :±15% Maximum); Rise Time: =583ns; Operating voltage RMS: CATI 600V CATII 600V CATIII 300V; 9V alkaline layer-built battery/ 15H

SSA3000X Plus-Refl(SW) & RB3X25(HW)

30 A Test Lead

Upgrade SDS2104X Plus bandwidth to 200 MHz

CAN FD serial triggering and decoding,software license

I2S serial triggering and decoding,software license

Rack Mount kit for SDS5000X

Advanced measurement kit ,including ACPR, CHPower, OBW and so on.

Reflect measurement kit(SW)

EMI Filter and Quasi Peak Detector, EMI Receiver Mode in EasySpectrum Software

25 MHz isolated USB function/arbitrary waveform generator,125 Msa/s,16 Kpts Arb Wave Length,Insulation Voltage, ±42 Vpk(Hardware)

High accuracy clock source

Bandwidth: 100 MHz; Maximum continuous current 30 Arms; Peak current 50 A; Switching ratio: 5 A/30;Accuracy: 5 A(±1%±1 mA); 30 A(±1%±10 mA); Standard DC12 V/1 A power adapter

Digital Bus Kit-LVDS (Without RF cables)

Mechanical Calibration Kit: OSLT, DC - 9 GHz, N-Female connector

Mechanical Calibration Kit: OSLT, DC - 4.5 GHz, 3.5mm SMA-Male connector

Mechanical Calibration Kit: OSLT, DC - 9 GHz, 3.5mm-Male and Female connector

N(M)-N(M) cable, 18 GHz

Active Probe, 2.5 GHz

5 pcs in a box, Pogo Tip,for SAP1000, SAP2500, SAP2500D;The pogo tip provides z axis compliance. The tip can fit into a socket or via and onto an IC leg.

SHS800X, SHS1000X current measurement accessory, 600 mA range

IQ Signal Generator Function (software)

Upgrade bandwidth from 200 MHz to 500 MHz

25 MHz built-in function generator option (software)

Manchester decode (SW)

200 MHz, 4 channels, 2 GSa/s, 12-bit high resolution, 200 Mpts memory depth mixed signal oscilloscope

Upgrade 350 MHz to 500 MHz (2-CH model),350 MHz model can not be upgraded to 1 GHz

Upgrade 500MHz to 1 GHz (4-CH model)

SENT trigger & decode (SW)

MIL-STD-1553B trigger & decode (software)

FlexRay trigger & decode (software)

Power Analysis: Power Quality, Current Harmonics, Inrush Current, Switching Loss, Slew Rate, Modulation, Output Ripple, Turn On/Off, Transient Response, PSRR, Efficiency

High Performance Reference Source

Enhanced Time-Domain analysis (SW)

Alligator clip to U type, length 600 mm, black and red as a pair

SPS5000X EIA Standard rack, height 3U

Pulse train generator (SW)

Magnetic Mounting for TA095

SMA(M)-SMA(M) cable, 18 GHz

EMI measurement mode (software license)

Pre-amplifier, 9 kHz ~ 26.5 GHz (software license)

Upgrade 13.6 GHz to 20 GHz (software license)

Pulse modulation (software license)