Specifications |
Analog Input |
Input Channels |
6 (Differential) |
Input Type |
+/-500 mV, +/-1V, +/-5 V, +/-10 V |
+0 mA ~ +20 mA, +/-20 mA, 4 ~ 20 mA (Jumper Selectable) |
Resolution |
Normal Mode |
16-bit |
Fast Mode |
12-bit |
Sampling Rate |
Normal Mode |
10 Samples/Sec.(Total) |
Fast Mode |
60 Samples/Sec. (Total) |
Accuracy |
Normal Mode |
+/-0.1% |
Fast Mode |
+/-0.5% or better |
Bandwidth |
Normal Mode |
15.7 Hz |
Fast Mode |
78.7 Hz |
Zero Drift |
+/-20 uV/°C |
Span Drift |
+/-25 ppm/°C
|
Input Impedance |
Voltage Input: 2M O, Current Input: 125 O |
Common Mode Rejection |
86 dB Min. |
Normal Mode Rejection |
100 dB |
Open Wire for Current Output |
4 ~ 20mA |
Over Protection |
240 Vrms |
ESD Protection |
+/-4 kV (Contact for each channel) |
+/-8 kV air for random point |
EFT Protection |
+/-4 kV for Power |
Analog Output |
Output Channels |
2 |
Span Drift |
+0 V~ +5 V, +/-5 V, +0 V~ +10 V, |
+/-10 V,+0 mA ~ +20 mA, +4 mA ~ +20 mA (jumper selectable) |
Resolution |
12-bit
|
Accuracy |
+/-0.1% of FSR |
Voltage Output Capability |
10 [email protected] mA |
Current Load Resistance |
500 Ohms |
Power-Up and SafeValue |
Yes |
Open Wire for Current Output |
4 ~ 20mA |
Digital Output |
Output Channels |
2 (Sink) |
Output Type |
Isolated Open Collector |
Max. Load Current |
700 mA/Channel |
Load Voltage |
5 VDC ~ 50 VDC |
External Power Reversed Protection and Short Circuit Protection |
Yes |
Over-Temperature Protection |
Yes, 150°C |
Current limited Protection |
1.1 A |
Digital Input |
Input Type |
2 (Dry+Wet)
|
Dry Contact(Source) |
On Voltage Level |
Close to GND |
Off Voltage Level |
Open |
Effective Distance for Dry Contact |
500M Max.
|
Wet contact |
On Voltage Level |
+1 VDC Max.
|
Off Voltage Level |
+3.5 VDC ~ +30 VDC |
Counters |
Channels |
2 |
Max. Counts |
16-bit (65535) |
Max. Input Frequency |
50 Hz |
Min. Pulse Width |
10 ms |
System |
CPU |
80186 CPU (80 MHz) |
SRAM |
512 KB |
Flash Memory |
512 KB |
EEPROM |
16 KB |
Dual Watchdog |
Yes |
Communication |
PoE Ethernet Port |
10/100 Base-TX (With Link, Activity LED Indicator) and automatic MDI/MDI-X |
2-way Isolation
|
Ethernet |
1500 VDC
|
AI, AO,DI and DO |
2500 Vrms
|
LED Indicators
|
PoE |
PoE On |
L1 |
Run |
L2 |
Link/Act
|
L3 |
10/100 M
|
Power Requirements
|
IEEE 802.3af |
Class 1 |
Required Supply Voltage |
Powered by Power-Over-Ethernet (PoE) or auxiliary power +12 ~ +48 VDC(non-regulated) |
LED Indicator |
Yes |
Power Consumption |
0.12 A @ 24 VDC Max. |
Mechanical
|
Dimensions (W x H x D) |
72 mm x 123 mm x 35 mm |
Installation |
DIN-Rail or Wall mounting |
Environment
|
Operating Temperature |
-25°C ~ +75 °C |
Storage Temperature |
-30°C ~ +80 °C |
Relative Humidity |
5 ~ 90% RH, non-condensing |
Software Specifications |
Functions |
36 IF-THEN-ELSE Logic Rules |
3 IF conditions with AND or OR operators |
3 THEN actions |
3 ELSE actions |
48 Internal Registers |
Hold temporary variables and read/write data via Modbus/TCP address. |
12 Timers |
Delay / Timing functions. |
12 Emails |
Send Email messages to pre-set Email receivers. |
Rule Configuration Website |
Access Web server on WISE controllers to edit and upload logic rules through web browser. |
Modbus/ TCP Protocol |
Real time control and monitoring I/O channels and system status of controllers via SCADA software. |
IF Conditions |
DI Channel |
ON, OFF, ON to OFF, OFF to ON, Change
|
AI Channel |
=, >, <, >=, <=(value) |
Internal Register
|
DI Counter |
=, >, <, >=, <=(value), Change |
DO Counter |
Timer |
Timeout, Not Timeout. |
THEN / ELSE Actions |
DO Channel |
ON, OFF, Pulse Output |
AO Channel |
Change the value |
Internal Register
|
DI Counter |
Reset |
DO Counter |
Timer |
Start, Stop |
Email |
Send |